Standardization Into The Main Theme: The Implementation Of The New Standard Plastic Pipe

Standardization Into The Main Theme: The Implementation Of The New Standard Plastic Pipe

According to the National Plastic Products Standard Of center said they “water with a hard polychlorinated Ethylene Pipe “And” Building PVC drainage pipe with a hard “two amendments of national standards has been completed, the revised draft has been adopted in December 2004 review of the standard is expected to be promulgated this year. The New Year, “the definition of biodegradable plastics, sorting and degradation of performance requirements,” the national standards began in January 7 comments, will soon be implemented. Also to be implemented, “the logo and signs of plastic products,” the national standard.

  This series of actions to remind all of plastic companies, standardization will be the year Plastics industry Development theme. Over the years, products, technology, equipment, standardization is not high plastic industry in China has been restricting the rapid Health Important factor in the development of China and also plastics manufacturer Competition Power is difficult to improve one of the reasons. When we were behind closed doors with their own competition, when companies can offer quick and tough plastic products to low labor costs and to replace the technical inputs such as counterfeiting cost advantage obtained by creating a boom period. However, China’s accession to WTO, the domestic market with the international trend to strengthen, and since last year, the surging prices of raw materials under the exposed catalytic domestic plastic industry, poor condition of scattered shows that this model has far can not meet the need for competition, and standardization from soft to hard the next few years will be the development of domestic plastic industry, an important way to standardization.

Recent years, the national authorities to increase the plastic formulation and revision of standards. Last year alone, the state amended the implementation of the plastic industry standards have ” Doors and windows Box with a hard polyvinyl chloride (PVC) profiles “and a dozen standard. National Development and Reform Commission issued a notice years ago showed that Poly Glycol Ester Carbonate Beverages Bottles, PVC double wall corrugated pipe such as 14 national standards have been approved and will be starting on June 1 this year, fully implemented. This is the industry standard in recent years, countries have ratified the largest number of plastic. Moreover, the more the industry Expert Recommendation to the industry standard nature of the some important recommendations to mandatory.

At the same time, from the standardization of the market demands more and more. To plastic Mold As an example. Since China’s standard rate is not high, making the mold design and manufacturing cycle than the foreign ministers of 25-40%, not only led to a number of extended delivery precision molds, manufacturing costs, but also cause the user to replace Parts Difficulties. It is understood that the market expected rate of domestic mold has standardized the past two years, 30% to 60% this year. Such expectations will demand changes through the reaction of the enterprise.

In addition, the standardization of plastic products in China is an important ticket to enter the international market. Standardized products do not enter the ranks of business can not be accepted by the international market, it can only form of processing to meet the needs of a very small part of the international market. The plastics business so that we will never be at the international division of labor can only be the most at the end, not to mention real access to international markets, much less about the international market.

This point of view, plastic companies to accept more formal, more powerful standard constraints are inevitable. In the process, Which company, which trades have to prepare more fully, in the future market, their odds will be greater.

I am a professional writer from China Manufacturers, which contains a great deal of information about head bands wholesale , hairbands, welcome to visit!

Article from articlesbase.com

Related Plastic Bottles Articles

Related Blogs

Technorati Tags: , , , , , , , , , , , , , , , , , , , , , , , , , ,

The Difference between a Bottled and Mains Fed Water Dispenser

The Difference between a Bottled and Mains Fed Water Dispenser

The main difference is the way water is delivered to the Water Dispenser.

Bottled Water Dispensers need:

– Water supplied from large plastic bottles, holding around 19 litres of water, installed on the top of the dispenser

– Some storage space nearby to hold a stock of bottles to prevent water running out

– Someone to change the water bottle when it becomes empty (when full they are heavy and awkward to move)

– Someone to make sure replacement bottles are ordered when stock runs low

– Connection to mains electricity if water is to be chilled

– Sanitising to ensure contamination through handling is kept at acceptable levels

In summary, Bottled Water Dispensers are convenient as they can be sited almost anywhere. The only restriction on location being access to mains power if the water is to be chilled. However, they need frequent attention by someone in the office or workplace to make sure the supply of water never runs out. Also the bottles (empty or full) take up valuable office space. The total footprint of the dispenser plus a sensible supply of bottles needs to be taken into account in any cost of ownership calculation.

The bottles, when full, weigh around 20kg, or 44lbs, so there is a Health and Safety risk whenever they need to be exchanged or moved around the office. The Health and Safety Executive General Risk Assessment Guidelines suggest that this weight should not be lifted above waist height by men; and not at all by women.

Mains-Fed Water Dispensers need:

– Connection to mains cold water – this is usually part of the installation process.
– There is no need to site the dispenser close to existing copper pipe as the connection is usually made using “food-grade” plastic pipe which can be run unobtrusively over quite large distances.
– Connection to mains power, for chilling and/or heating the water at the point of use.
– Sanitisation of the internal components regularly and effectively.

Since there are no bottles the total footprint is much smaller as there are no bottles to store nearby. This also means there are no heavy weights to carry or empty bottles to dispose of. Once installed there is no other administrative overhead in terms of managing supplies or reordering, or in time spent changing empty bottles for full ones.

These are the main reasons we only supply Mains-Fed Water Dispensers for either chilled, ambient or hot water. There are others so see below in a later section on Ten Reasons why your office needs a Mains-Fed Water Dispenser.

Chris Wills is the Sales Director for Freshwater Coolers PLC. http://www.freshwatercoolers.com is one of the UK’s largest suppliers for a hot or cold water dispenser, supplying and maintaining high quality equipment for the workplace. Our main philosophy is to provide a service which consistently exceeds customers’ expectations.

Call 0800 169 4008 or Click this Link http://www.bestwaterdispenser.co.uk to Download our Water Dispenser Buyer’s Guide” This Free Guide will help you make the correct choice when buying a Water Cooler or Hot Water Dispenser. Packed full of tips and advice to save you money!

Article from articlesbase.com

www.ocme.it Altair N60 wraparound packer running at 60 packs per minute. Equipped with extra blank magazine for higher autonomy.

Related Blogs

Technorati Tags: , , , , , , , , , , , , , , , , , , , , , , , , ,

Summary Of The Week News Plastics Industry (4.27

Summary Of The Week News Plastics Industry (4.27

Plastic net HC Plastics market this week (4.27-4.30) the overall trend to settle, the atmosphere in the shadow of depression, the trend of a strong rebound is difficult! However, under the influence of warming in the early stage, many companies still have options start, expect to take the ice out. In opening the Chinese market, Recycled plastic Cosmetic bottles and plastic packaging materials have demonstrated very strong, PE / PP speculation reburning war, many companies report first quarter results have exposure, has also brought progress in a volatile market of plastic … …

HC Aspect: 4 plastics market analysis and market forecast in May

The international market: in April in Asia Polyethylene Market quotations are: high-pressure 1150 U.S. dollars / ton, low-voltage 1160 U.S. dollars / ton, linear 1140 U.S. dollars / ton (CFR China / Southeast Asia). April Asia Polypropylene Price spikes were 60 dollars, reported 1100 (all together) -1 150 (copolymer) dollars / ton, trading quiet. Of the domestic market in April: April polyethylene market trend continued in March of the wave-market: the market in early April due to increased demand and the sharp drop in imports of resources and external disk deadly accuracy, as well as domestic petrochemical enterprises frequently pull up the price of spirits, once there warming potential, the polyethylene market activities

More information, please see: http://info.plas.hc360.com/2009/04/28112961467.shtml

Plastic material – cosmetic packaging “rising star”

For people Food Packaging plastic packaging mentioned the issue of security worries, in the cosmetics industry, so far, or not found. In fact, today’s cosmetic packaging materials can be divided into three categories: one is plastic packaging materials, including Plastic Pipe , Plastic boxes, plastic bags and plastic bottles, etc., is known as cosmetic plastic bottle packaging materials “rising star”

More information, please see: http://info.plas.hc360.com/2009/04/29074261541.shtml HC

3 Plastic Additives Market analysis Plastic mesh data, according to HC, in March 2009 HC plastic additives market, the situation of concern, compared with last month, attention focused on specific products, the overall concern in good condition. Specific products, Plasticizer 2%, flame retardant 1%, 2% masterbatch, calcium carbonate 1%, filler, reinforcing agent such as 1% of toughening. Spot area (in DOP as an example): DOP in Eastern China by the end of March fell 200 yuan / ton to 8,800 yuan / ton

More information, please see: http://info.plas.hc360.com/2009/04/27082261304.shtml

In crisis quietly rising China Powder Industry

08 by the U.S. subprime mortgage crisis has triggered a financial crisis for the global economy has a huge negative impact on the global capital market in ruins, the economy, industry, plastics industry spared powder industry in China has been very significant impact. Financial crisis and dangerous phenomena on the surface, in fact, the industry reshuffle is conducive to survival of the fittest, business development opportunities. And Powder industry is a very humble profession, many people will not notice such a business, but in this world-class economic crisis struck, the Chinese industry to buck the trend growth of powder, quietly rising

More information, please see: http://info.plas.hc360.com/2009/04/30082261687.shtml

I am China Quality Digital writer, reports some information about electricians tool set , air reversible drill.

Article from articlesbase.com

Related Blogs

Technorati Tags: , , , , , , , , , , , , , , , , , , , , , , , , ,